爱波彩票APP下载

成品万能支撑器厂家杭州比模特科技爱波彩票APP下载主要经营喷泉景观支撑器,防腐木支撑器,木塑支撑器,水景支撑器等,提供万能支撑器安装与价格报价业务,若大家有万能支撑器、万能支撑架、地板支架或塑木龙骨支架的需要,请联系:0571-86221809

NEWS 新闻中心

NEWS CENTER

  • 万能支撑器施工方法
  • 本站编辑:杭州比模特科技爱波彩票APP下载发布日期:2019-03-28 14:06 浏览次数:

万能支撑器的具体施工方法可细分为9个步骤:

  1、策划

  先做好策划方案,以施工大样图和加工单为依 据,熟悉了解各部位尺寸和做法,尤其落实好地面Led灯带及边角等部位之间的关系,避免收口处出现问题。

  2、基层处理

  将广场垫层上的杂物清理干净,并用钢丝刷刷掉粘结在垫层上的砂浆。要求地面相对平整,不要出现局部高低起伏现象,避免底基座底面不能够完全与地面相接触造成不稳,水泥地面哑光面即可。根据图纸所示标高并结合石材厚度确定万能支撑器高度,再通过左右旋转各部件可以调节所需高度,不要旋得过于紧密,也不要旋出指示范围,按产品上箭 头标示操作使用才能发挥出该产品的最佳使用状态。

  3、检查和控制支撑器位置

  依据施工大样图及广场实际尺寸,在广场上拉十字控制线,弹在基层上,并引至墙面底部,然后找出面层标高,在墙上弹出水平标高线,同时弹出支撑器中心线,进行试排。把花岗岩石材排好,以便检查石材之间的缝隙,核对石材与墙面、灯带、洞口等部位的相对位置。

  4、排水

  可采用暗排水构造。基层为了排水方便一般具有一定坡度,但是完成面必须保持水平。例如,一工程结构基础为4%的坡度,要求完成面保持水平。

  5、找坡

  万能支撑器找坡范围1%~5% ,控制坡度关 键部件为调节件。施工时应首先将调节件上找坡调整到4% ,再将找坡箭头中的4%调整指向找坡方向,然后整体铺装时按照先前调整好的找坡度依次展开。这样将完全抵消结构找坡带来的面层不平整问题,对于大面积石材铺贴施工中控制平整度具有很大的优势,精确度非常高。

  6、留缝

  留缝的作用一方面可以处理石材规格不整的问题 ,同时也是给排水、热胀冷缩预留位置。缝隙主要依靠调节件控制,调节件分2、4、5、6、8、10 mm共6个型号,依据实际需求选择调节件。调节件可严格控制留缝精度,消除人为因素,从而在外观上达到整齐划一的目的,提高美观效果,这也    是有别于常规做法的优点之一。

  7、平整度检查

  首先任选一块石材,用水平尺按对角线的方向放下,检查是否平整,然后测定每2块上下左右相邻的石材,若平整则水平尺中间的水珠应该在中间。最后检查边角是否对直,从实际检验结果来看效果非常好。地面LED灯带的灯具依据石材高度定做,坐落在万能支撑器之上。灯具相关线缆、控制系统、电源等从底部架空层敷设,灯带面层与灯具相互独立。面层选用定制钢化玻璃,灯带两侧石材开槽以便安置玻璃,开槽规格为10mm ,通过耐候胶将玻璃固定在两侧石材小槽上。这种做法一方面保证了灯带核心部件即灯具不受承压破坏,更重要的是便于检修,更换灯具、线缆等工作。

  8、分隔片的使用

  使用时有一些应用技巧,例如4个分隔片宽度均为10mm宽,其中可以去掉若干个分隔片应对特殊安装情况使用,例如在不需要分隔的边角等部位使用;同样底座安装时遇到特殊情况也可以切除,例如支撑器底部附件有障碍物,进而影响面层石材铺贴的模数,在此情况下可适当切除相应部位。

爱波彩票APP下载  9、石材厚度不均的处理

  石材在加工过程中往往存在着厚度不均的瑕疵。在安装石材过程中,石材万能支撑器可以通过垫片进行调节进而消除石材自身的误差。如垫片规格分为1mm 及2mm 厚,根据石材厚度相差的情况可自行增减垫片进行调整。

l2-1P62Q61542-50_267_210[1].jpg

The specific Shigongfangfa of the universal support can be subdivided into 9 steps:
1, planning
First, plan the plan to use the construction sample map and the processing sheet as the basis, and be familiar with the size and practices of the various parts。 In particular, implement the relationship between the surface Leld and the edges and other parts to avoid problems at the closing point。
2, grassroots treatment
Clean up the debris on the square cushion and brush off the mortar bonded to the cushion with a wire brush. The ground is required to be relatively flat, without local ups and downs, to avoid the bottom of the base can not completely contact the ground to cause instability, cement surface matte surface can be. The height of the universal support device is determined according to the elevation shown in the drawings and combined with the thickness of the stone. Then the required height can be adjusted by rotating each component to the left and right. Do not spin too closely, and do not spin out the indication range. The best use of the product can be achieved by using the arrow on the product.
3, check and control support position
According to the construction sample map and the actual size of the square, pull the cross control line on the square, bomb it on the base, and lead it to the bottom of the wall。 Then find the floor elevation, pop up the horizontal elevation line on the wall, and pop up the center of the support device。 Line, test row。 Arrange the granite stone in order to check the gap between the stone and check the relative position of the stone and the wall, lampstrip, hole and other parts。
4, drainage
Dark drainage structures can be used. The basic level generally has a certain slope for the convenience of drainage, but the completion surface must be maintained at a level. For example, an engineering structure is based on a slope of 4 inches, requiring the completion surface to be maintained at a level.
5, looking for a slope
The universal support finds the slope range of 1 <UNK> ~ 5 <UNK>, and the control slope key off part is the adjusting part. During construction, the adjustment shall first be adjusted to 4 points on the adjustment part, and then the 4 points in the search arrow shall be adjusted to the search direction, and then the overall paving shall be carried out in order to follow the previously adjusted search slope. This will completely offset the problem of uneven surface layer caused by the structural slope, which has great advantages and high accuracy for controlling the smoothness in the construction of large areas of stone paving.
6, leave seam
On the one hand, the function of the remaining seam can deal with the problem of incomplete stone specifications, and it is also reserved for water supply and drainage, hot expansion and cooling。 The gap mainly depends on the adjustment part control, the adjustment part is divided into 2, 4, 5, 6, 8, 10m a total of 6 models, according to actual needs selected adjustment parts。 The adjustment parts can strictly control the accuracy of the remaining seams and eliminate human factors, so as to achieve the goal of uniformity in appearance and improve the aesthetic effect。 This is also one of the advantages that is different from the usual practice。
7, flatness inspection
First of all, select a piece of stone, put it down in the diagonal direction with a horizontal ruler, check whether it is flat, and then determine the stone adjacent to each of the two blocks. If it is flat, the water ball in the middle of the horizontal ruler should be in the middle. Finally check whether the edge angle is straight, from the actual test results show that the effect is very good. The lamps on the LED light belt on the ground are customized according to the height of the stone and are located on the universal support device. Lamp related cables, control systems, power supply, etc. are laid from the bottom shelf layer, and the lamp surface layer and the lamp are independent of each other. The surface layer is made of custom tempered glass, and the stone on both sides of the light belt is slotted to fit the glass. The slot specification is 10mm. The glass is fixed to the small stone troughs on both sides through weather resistant glue. On the one hand, this approach ensures that the core parts of the lampstrip, namely, the lamps, are not damaged by pressure, and more importantly, it is easy to overhaul, replace lamps, cables, and other work.
8, the use of separators
There are some application techniques when using, such as four separators with a width of 10m wide, in which several separators can be removed for special installation situations, for example, in parts such as edges that do not require separation; When the same base is installed, special conditions can also be removed. For example, there is an obstacle at the bottom of the support device, which in turn affects the modulus of the surface layer stone paving. In this case, the corresponding part can be appropriately removed.
9, the treatment of stone thickness uneven
Stone in the process of processing, there are often uneven thickness of the defects. In the process of installing stone, the stone universal support can be adjusted by the gasket to eliminate the error of the stone itself. If the gasket specification is divided into 1M M and 2m thick, according to the difference in the thickness of the stone, the gasket can be adjusted by itself.

Copyright 2018-2020 版权所有:杭州比模特科技爱波彩票APP下载 All Right Reserved

湖北快三走势图 湖北快3走势图 博旺彩票APP下载 乐仑彩票平台 博盛彩票APP下载 大星彩票APP下载 湖北快3走势图 湖北快3走势图 安徽快3开奖结果 百易彩票APP下载